How to Fix Slow File Transfers on Windows

Published 2026-10-16 · Marion Remote Fix

File transfers are painfully slow — copying files to a USB drive takes forever, transferring files over your local network crawls, or moving large files between folders on the same computer is much slower than expected. Slow file transfers are caused by hardware limitations, outdated drivers, Windows settings that throttle performance, or disk health issues. Here is how to diagnose and fix slow transfers.

Identify where the bottleneck is

Before fixing anything, figure out what kind of transfer is slow so you target the right cause:

  • USB drive transfers: the speed depends on the USB version (USB 2.0 maxes out around 30-40 MB/s, USB 3.0 can reach 100-400 MB/s, USB 3.2 Gen 2 can reach 800+ MB/s) and whether the drive itself is fast enough. Check what the transfer speed actually is by watching the Windows copy dialog — it shows the speed in MB/s
  • Network transfers: transferring files to another computer on your network. Speed depends on your network connection (Wi-Fi is slower than Ethernet, and the slowest device in the chain sets the limit)
  • Same-drive transfers: moving files within the same physical drive. On HDDs this is slow because the drive head has to read and write simultaneously. On SSDs it should be fast
  • Between drives: copying from one internal drive to another. Speed is limited by the slower of the two drives

Fix slow USB transfers

If copying to or from a USB flash drive or external hard drive is slow:

  1. Check the USB port version: plug your USB 3.0 device (blue connector or marked SS for SuperSpeed) into a USB 3.0 port on your computer (also blue, often on the back of desktops). A USB 3.0 device in a USB 2.0 port runs at USB 2.0 speed — about 10 times slower
  2. Check for USB 2.0 fallback: open Device Manager → expand Universal Serial Bus controllers. If you see your device listed under a USB 2.0 hub instead of USB 3.0, try a different port or check if USB 3.0 drivers need updating
  3. Update USB drivers: Device Manager → Universal Serial Bus controllers → right-click USB Root Hub (USB 3.0) → Update driver. Also check your motherboard manufacturer's website for chipset and USB drivers
  4. Change the removal policy: Device Manager → Disk drives → right-click the USB drive → Properties → Policies tab. Select Better performance instead of Quick removal. This enables write caching and can significantly speed up writes. Note: with this setting, you must always use Safely Remove Hardware before unplugging the drive to avoid data loss
  5. Format for speed: if the USB drive is formatted as FAT32, it cannot handle files larger than 4 GB and has higher overhead for many small files. Reformatting as NTFS or exFAT improves performance, especially for large files. Warning: formatting erases all data on the drive — copy everything off first
  6. Try a different cable: for external hard drives with a USB cable, a damaged or low-quality cable can reduce speeds. Try the cable that came with the drive

Fix slow network file transfers

If transferring files between computers on your local network is slow:

  1. Use Ethernet instead of Wi-Fi: gigabit Ethernet can transfer at 100-120 MB/s. Wi-Fi 5 (802.11ac) typically gets 20-60 MB/s in practice, and Wi-Fi 4 (802.11n) is even slower. If you need fast network transfers, plug both computers into the router with Ethernet cables
  2. Check your network adapter speed: open Settings → Network and Internet → click your connection → Hardware properties. Look for Link speed — it should say 1 Gbps for gigabit Ethernet. If it says 100 Mbps, you have a Fast Ethernet adapter, a 100 Mbps switch, or a Cat5 cable limiting speed (use Cat5e or Cat6)
  3. Disable SMB encryption: Windows 11 enables SMB encryption by default for some connections, which adds processing overhead. In PowerShell as administrator: Set-SmbClientConfiguration -RequireSecuritySignature $false. Only do this on trusted home networks
  4. Update the network adapter driver: Device Manager → Network adapters → right-click your adapter → Update driver. Also check your motherboard or laptop manufacturer's website
  5. Disable Large Send Offload: Device Manager → Network adapters → right-click your adapter → Properties → Advanced tab → find Large Send Offload V2 (IPv4) and set to Disabled. This feature can sometimes reduce transfer speeds rather than improve them
  6. Check for background network usage: OneDrive, Dropbox, cloud backups, Windows Update, or other devices on the network may be consuming bandwidth during your transfer. Pause syncing services while transferring large files

Fix slow transfers on the same computer

If copying files between folders or between drives on the same computer is slow:

  1. Check drive health: open Command Prompt as administrator → run wmic diskdrive get status. If any drive shows anything other than OK, it may be failing. Use CrystalDiskInfo for detailed SMART health data — look for reallocated sectors, pending sectors, or current pending errors
  2. Defragment HDDs: if copying to or from a traditional hard drive (not SSD), fragmentation slows reads and writes. Search for Defragment in Start → Defragment and Optimize Drives → select the HDD → Optimize. Do NOT defragment SSDs — Windows trims them automatically
  3. Check if the drive is full: drives slow down significantly when they are nearly full. HDDs slow down as they fill because remaining space is on the slower outer tracks. SSDs slow down when full because they run out of free blocks for wear leveling. Keep at least 10-15% free space on any drive
  4. Check SATA connection: for internal drives, a loose SATA cable or a drive connected to a slower SATA port can reduce speed. SATA III (6 Gbps) is standard for modern drives — check your motherboard manual to confirm which ports are SATA III
  5. Enable AHCI mode: check your BIOS for a SATA mode setting. It should be AHCI, not IDE. IDE mode limits SATA performance. Warning: changing this setting after Windows is installed can cause a boot failure — research the proper procedure for your Windows version before changing it

Disable Windows features that slow transfers

Several Windows features add overhead to file operations:

  • Remote Differential Compression: this feature is intended for network transfers but can slow them down. Turn it off: Control Panel → Programs → Turn Windows features on or off → uncheck Remote Differential Compression API Support
  • Windows Search indexing: if the indexer is scanning files while you are transferring, it competes for disk access. Pause indexing during large transfers: search for Indexing Options → Advanced → Pause indexing
  • Antivirus real-time scanning: your antivirus scans every file as it is copied, which can halve transfer speeds for many small files. Most antivirus software lets you temporarily disable real-time protection or add an exclusion for the destination folder during the transfer. Re-enable it after
  • File compression: if the destination folder has NTFS compression enabled (Properties → Advanced → Compress contents), every file is compressed during the copy, which slows the transfer significantly. Disable compression on the destination folder if speed is more important than space savings

Speed up many-small-file transfers

Copying thousands of small files (photos, source code, game saves) is much slower than copying the same total size as a few large files because of per-file overhead:

  • Archive first: zip or compress the files into a single archive before transferring. A single 2 GB zip file transfers much faster than 50,000 small files totaling 2 GB. Extract after the transfer
  • Use Robocopy: open Command Prompt → robocopy source destination /E /MT:16. The /MT:16 flag uses 16 threads for parallel copying, which dramatically speeds up many-small-file transfers compared to the Windows copy dialog. Adjust the thread count (8-32) based on your hardware
  • Use TeraCopy: a free third-party copy tool that handles queuing, verification, and error recovery better than Windows Explorer. It often transfers faster because it optimizes the read/write pattern

Check for malware

Malware can consume disk and network bandwidth, making all transfers slow:

  1. Open Task Manager → Performance tab. If disk usage is high (near 100%) even when you are not actively copying files, something is using the disk in the background
  2. Check the Processes tab → sort by Disk to find what is consuming disk access
  3. Run a full scan with Windows Defender and a second scan with Malwarebytes to check for malware consuming resources

Remote file transfer troubleshooting

If your file transfers are still slow after trying these fixes, Marion Remote Fix can diagnose the problem remotely — checking drive health, network configuration, USB settings, and system performance through a secure remote session.

← Back to Blog