How to Boot into Safe Mode and Troubleshoot Windows
Published 2026-10-16 · Marion Remote Fix
Your computer crashes, shows a blue screen, freezes during startup, or runs so poorly that you cannot use it normally. Safe Mode is a diagnostic startup mode that loads Windows with a minimal set of drivers and services — only what is absolutely necessary for the operating system to function. By stripping away third-party drivers, startup programs, and non-essential services, Safe Mode lets you isolate whether a problem is caused by something Windows loads during normal startup.
What Safe Mode does
- Safe Mode loads a basic video driver (low resolution, no hardware acceleration), minimal network support (only in Safe Mode with Networking), and only essential Windows services. Third-party drivers, startup programs, and non-critical services are not loaded
- The screen resolution is lower and the display looks different because the basic video driver replaces your GPU driver. The desktop shows Safe Mode in the corners of the screen. Performance may feel different because hardware acceleration and many background services are not running
- If a problem disappears in Safe Mode, the cause is something that loads during normal startup but not in Safe Mode — a third-party driver, a startup program, or a non-essential service. If the problem persists in Safe Mode, it is caused by a core Windows component or hardware issue
Boot into Safe Mode from Settings
- If Windows starts normally (even if unstable), you can access Safe Mode through Settings. Open Settings, System, Recovery. Under Advanced Startup, click Restart Now. The computer restarts to the recovery environment
- Select Troubleshoot, then Advanced Options, then Startup Settings, then Restart. After the computer restarts again, a numbered list appears. Press 4 for Safe Mode, 5 for Safe Mode with Networking, or 6 for Safe Mode with Command Prompt
- Safe Mode with Networking is usually the best choice because it enables network drivers, allowing you to download driver updates, run Windows Update, or access network resources while troubleshooting
Boot into Safe Mode when Windows will not start
- If Windows crashes before you can reach Settings, you can force the recovery environment by interrupting startup three times. Power on the computer. When you see the Windows logo or spinning dots, hold the power button for 10 seconds to force a shutdown. Repeat this three times
- On the fourth startup attempt, Windows enters Automatic Repair mode. If it says Preparing Automatic Repair or Diagnosing Your PC, let it proceed. When the recovery screen appears, select Advanced Options, then Troubleshoot, Advanced Options, Startup Settings, Restart. Then press 4, 5, or 6 for Safe Mode
- If the three-interrupt method does not work, you can use a Windows installation USB drive. Boot from the USB, select your language, click Next, then click Repair Your Computer in the lower left. This opens the same recovery environment where you can access Startup Settings and Safe Mode
Troubleshoot in Safe Mode
- Once in Safe Mode, try to reproduce the problem. If the computer no longer crashes, freezes, or shows errors, a third-party component is the cause. Common culprits are recently installed drivers (especially GPU drivers), recently installed software, antivirus programs, and startup items
- Uninstall recently installed software or drivers. Open Settings, Apps, Installed Apps, and sort by install date. Uninstall the most recently installed programs that may be causing the issue. For driver problems, open Device Manager, find the device, and roll back or uninstall the driver
- If the problem started after a Windows Update, uninstall the update. Open Settings, Windows Update, Update History, Uninstall Updates. Remove the most recent update and restart normally to test
Run malware scans in Safe Mode
- Malware that interferes with antivirus software during normal startup may be unable to protect itself in Safe Mode because its startup components are not loaded. Boot into Safe Mode with Networking and run a full malware scan
- Open Windows Security, Virus and Threat Protection, Scan Options, and select Full Scan. The scan runs without interference from malware that may block it during normal operation. Also consider downloading and running Malwarebytes in Safe Mode for a second-opinion scan
- If malware is found and removed, restart normally and run another scan to confirm the system is clean. Some malware has multiple components — one may be removed while another survives to reinstall it
Fix driver problems in Safe Mode
- If a new GPU driver causes blue screens or display problems, Safe Mode bypasses that driver entirely (using the basic display driver). Open Device Manager in Safe Mode, expand Display Adapters, right-click the GPU, and select Uninstall Device. Check Remove Driver Software. Restart normally and Windows uses a basic driver. Then install a known-working GPU driver version
- For any driver causing crashes, the same approach works: uninstall the driver in Safe Mode, restart normally, and install a corrected version. Device Manager in Safe Mode shows all devices even though their full drivers are not loaded
Use System Restore in Safe Mode
- System Restore can revert the system to a state before the problem started. In Safe Mode, search for Create a Restore Point, click System Restore, and select a restore point dated before the problem began. System Restore returns system files, drivers, and registry settings to that point without affecting personal files
- System Restore is available in Safe Mode even when it cannot run during normal startup (because the problem preventing normal startup may also prevent System Restore from completing). Safe Mode provides a more stable environment for the restore process
Check startup programs
- Open Task Manager in Safe Mode (Ctrl plus Shift plus Escape) and go to the Startup tab. This shows all programs configured to start with Windows. Disable suspicious or unnecessary startup items by right-clicking them and selecting Disable
- If you are unsure which startup item is causing problems, disable all of them, restart normally, and re-enable them one at a time. When the problem returns after enabling a specific item, that item is the cause
Repair Windows files in Safe Mode
- Open Command Prompt as Administrator in Safe Mode and run sfc /scannow. The System File Checker scans all protected system files and repairs corrupted ones. This is more likely to succeed in Safe Mode because fewer files are locked by running processes
- If SFC reports files it cannot repair, run DISM /Online /Cleanup-Image /RestoreHealth to repair the component store first. Then run SFC again. These repair operations often resolve blue screens, crashes, and startup failures caused by corrupted system files
Exit Safe Mode
- To exit Safe Mode, simply restart the computer normally. It boots into the standard Windows mode with all drivers and services loaded. If you booted into Safe Mode using the Startup Settings method, a normal restart returns to normal mode automatically
- If the computer keeps booting into Safe Mode after restarting, the Safe Mode boot flag may be set. Open the System Configuration tool (search for msconfig), go to the Boot tab, and uncheck Safe Boot. Click OK and restart. The computer boots normally
Need help troubleshooting?
If you need to troubleshoot a Windows problem in Safe Mode but are not confident performing the diagnosis yourself, Marion Remote Fix can guide you through booting into Safe Mode and then remotely diagnose the issue, remove problematic drivers or software, run repairs, and get your computer running normally again.